отказ ПЛК110-60 М02

[Валенок]

..........
В ремонт.

[alexx751]

Вот лог загрузки. идет по кругу.

Owen loader 1.04

CPU:AM1808
DDR Memory:MICRON 64 MB 150 MHz

TEST OK!
NAND Memory: ID = 194, size = 128M
Valid magicnum, 0x55424CBB, found in block 0x00000006.
Jump to entry point
at: 0xC0000000
Factory setings detected
Found 18 notes in 4 products
SOM01C04 or later detected -> configure RMII clock directly
Auto 485 hardware detected
Waiting for check power...
Power status OK
Initialization of Power control completed

Last run module Id =0
Last post module Id =0
local_status =0
Init I2C
Driver for address 77 found
Driver for address 72 found
Begin search and initialize I2C devices
Check for address 77 ...DEVICE FOUND!
MCP9800 #0 OK!
Check for address 72 ...FAILED!
OSC_lev1
OSC_lev2
OSC_lev3
Detect modules
Found module #0
Init group
MRAM init
Init MRAMCheck copies...First OK...Second OK...Copies number: 13 14
Actual copy is 1
USB MSD InitINIT: Init started. Version 1.14.02
INIT: USBH_PreInit!
INIT: USBH_X_Config()
...Init FTDI Stack OK
.OK
FS Init....High-level format ram
OK
Retain mode - save on powerfall
PFM
INIT: Init started. Version 2.13.11

Owen loader 1.04

CPU:AM1808
DDR Memory:MICRON 64 MB 150 MHz

TEST OK!
NAND Memory: ID = 194, size = 128M
Valid magicnum, 0x55424CBB, found in block 0x00000006.
Jump to entry point
at: 0xC0000000
Factory setings detected
Found 18 notes in 4 products
SOM01C04 or later detected -> configure RMII clock directly
Auto 485 hardware detected
Waiting for check power...
Power status OK
Initialization of Power control completed

Last run module Id =-1383112377
Last post module Id =-1574253439
local_status =70102
Init I2C
Driver for address 77 found
Driver for address 72 found
Begin search and initialize I2C devices
Check for address 77 ...DEVICE FOUND!
MCP9800 #0 OK!
Check for address 72 ...FAILED!
OSC_lev1
OSC_lev2
OSC_lev3
Detect modules
Found module #0
Init group
MRAM init
Init MRAMCheck copies...First OK...Second OK...Copies number: 13 14
Actual copy is 1
USB MSD InitINIT: Init started. Version 1.14.02
INIT: USBH_PreInit!
INIT: USBH_X_Config()
...Init FTDI Stack OK
.OK
FS Init....High-level format ram
OK
Retain mode - save on powerfall
PFM
INIT: Init started. Version 2.13.11

Owen loader 1.04

CPU:AM1808
DDR Memory:MICRON 64 MB 150 MHz

TEST OK!
NAND Memory: ID = 194, size = 128M
Valid magicnum, 0x55424CBB, found in block 0x00000006.
Jump to entry point
at: 0xC0000000
Factory setings detected
Found 18 notes in 4 products
SOM01C04 or later detected -> configure RMII clock directly
Auto 485 hardware detected
Waiting for check power...
Power status OK
Initialization of Power control completed

Last run module Id =-309333689
Last post module Id =-1557609328
local_status =70102
Init I2C
Driver for address 77 found
Driver for address 72 found
Begin search and initialize I2C devices
Check for address 77 ...DEVICE FOUND!
MCP9800 #0 OK!
Check for address 72 ...FAILED!
OSC_lev1
OSC_lev2
OSC_lev3
Detect modules
Found module #0
Init group
MRAM init
Init MRAMCheck copies...First OK...Second OK...Copies number: 13 14
Actual copy is 1
USB MSD InitINIT: Init started. Version 1.14.02
INIT: USBH_PreInit!
INIT: USBH_X_Config()
...Init FTDI Stack OK
.OK
FS Init....High-level format ram
OK
Retain mode - save on powerfall
PFM
INIT: Init started. Version 2.13.11

Owen loader 1.04

CPU:AM1808
DDR Memory:MICRON 64 MB 150 MHz

TEST OK!
NAND Memory: ID = 194, size = 128M
Valid magicnum, 0x55424CBB, found in block 0x00000006.
Jump to entry point
at: 0xC0000000
Factory setings detected
Found 18 notes in 4 products
SOM01C04 or later detected -> configure RMII clock directly
Auto 485 hardware detected
Waiting for check power...
Power status OK
Initialization of Power control completed

Last run module Id =-1517293241
Last post module Id =-1574255487
local_status =70102
Init I2C
Driver for address 77 found
Driver for address 72 found
Begin search and initialize I2C devices
Check for address 77 ...DEVICE FOUND!
MCP9800 #0 OK!
Check for address 72 ...FAILED!
OSC_lev1
OSC_lev2
OSC_lev3
Detect modules
Found module #0
Init group
MRAM init
Init MRAMCheck copies...First OK...Second OK...Copies number: 13 14
Actual copy is 1
USB MSD InitINIT: Init started. Version 1.14.02
INIT: USBH_PreInit!
INIT: USBH_X_Config()
...Init FTDI Stack OK
.OK
FS Init....High-level format ram
OK
Retain mode - save on powerfall
PFM
INIT: Init started. Version 2.13.11