Сообщение от
Николаев Андрей
Если не сложно - лог терминала
Не сложно:
Код:
DATAFLASH initialized successful
Welcome to the OWEN program loader 1.3
Kernel found...
Loading kernel...
Reseting...
Checksum OK!
Load PLC core...
Main oscilator clock=16001024
Processor clock=180011520
Master clock=60003840
Waiting for check power...
Power status OK
Initialization of Power control completed
at 20080004, s=12
Initialization of Timer0 completed
Module Id=1 found
Module Id=2 found
Module Id=3 found
Module Id=103 found
Module Id=104 found
Module Id=120 found
Module Id=125 found
Module Id=126 found
Module Id=131 found
Module Id=190 found
Module Id=199 found
Module Id=200 found
Module Id=2000 found
Module Id=2050 found
Module Id=2051 found
Module Id=2052 found
Module Id=2053 found
Module Id=2054 found
Module Id=2055 found
Module Id=2056 found
Module Id=2057 found
Module Id=2058 found
Module Id=2059 found
Module Id=2060 found
Module Id=2061 found
Module Id=2062 found
Module Id=2063 found
Module Id=2064 found
Module Id=2065 found
Module Id=201 found
Module Id=202 found
Module Id=203 found
Module Id=210 found
Module Id=2100 found
Module Id=211 found
Module Id=250 found
Module Id=302 found
Module Id=303 found
Module Id=450 found
Module Id=451 found
Module Id=452 found
Module Id=562 found
Module Id=563 found
Module Id=570 found
Module Id=571 found
Module Id=599 found
Module Id=600 found
Module Id=601 found
Module Id=602 found
Module Id=650 found
Module Id=130 found
Module Id=221 found
Module Id=300 found
Module Id=531 found
Module Id=400 found
Module Id=402 found
Module Id=401 found
Initialization of Timer5 completed
Initialization of Timer4 completed
Test Complited USB slot is present in PLC!!!
Host is not connected
Start init USB driver !!!
Start init USB - Serial number OK.
Initialization of USB device CDC completed
Begin search and initialize I2C devices
Check for adress 77 ...DEVICE FOUND!
MCP9800 #0 OK!
Check for adress 72 ...FAILED!
Check for adress 6 ...DEVICE FOUND!
PIC upper initialized!
at 20080038, s=4
Read Flash: .at 20080040, s=4
at 20080048, s=4
.....................at 20080050, s=4
...............................................................................
DATAFLASH READ OK
Flash read takes 4329 ms
Start mounting FFS
Flash check takes 2531 ms
It is 1 bad blocks
Mounting of FFS completed!
Mounting takes 179 ms
Total size of filesystem is 3145728 bytes
It is 6002 blocks
It is 141 used blocks
It is 1 bad blocks
Maximum wear level is 12 times
Reset status information.......................
PLC was reset by power!
Last run module Id =-1874281634
Last post module Id =-843971829
Total control code =1719154573
Max cache utilisation =-471080746
local_status =25e89a82
run_level =42
Run levels stack: 23 5c 19 be 2f 87 b0 40 7f 35 ad ec 58 7d 8b ab
................................................
Slave Retain loaded
at 200800a0, s=28
PLC model MODEL PLC 160
Binary VERSION 2.14.0
Need Target version 2.10
Compiled: 10:35:22 Apr 29 2011
MAC 6A:77:00:21:80:3D
IP 10.0.6.10
GATE 10.0.6.1
MASK 255.255.255.0
PIC upper version is 15
Licence limited to 360 bytes
Loading PLC core completed!
Start CoDeSys initialization secuence
Initialization of USB device CDC completed
Special cable detected...
Switch top RS to CoDeSys mode...
Для Дмитрия Артюховского: честно говоря боюсь уже "прошивать" - зависнет что-нибудь - опять месяц ждать, когда с ремонта вернётся...